Peugeot 3008 Key Fob Problems
Peugeot's mid-sized 3008 SUV has lot going for it. It's smooth to drive, looks good and has a big boot. Can it compete in the most competitive segment of the market, perhaps?
If your Peugeot keyfob does not work it could have been exposed to soapy or clean tap water. It may be necessary to remove the battery, then clean it with isopropyl ethanol or electronic cleaner.
Dead coin battery
Peugeot key fobs have tiny coin batteries that powers their remote locking as well as other features. The battery is a bit dated and may wear out after years of usage. A simple way to check whether the battery is in good condition is to perform the voltage test. A multimeter can determine the voltage between the battery's plus and negative poles. This test will tell you whether the battery is dead.
The receiver module may be the reason for your key fobs not working after having used your Peugeot 3008 a long time. The receiver module is in charge of receiving radio frequency signals transmitted by key fobs and then sending them to the car's systems. If the receiver module is defective and not functioning properly, it won't be able to send commands to the other modules in the vehicle.
Another common cause for an unusable key fob is moisture or sweat that has accumulated on the circuit board. This can lead to short circuits that drain the battery, and can also cause the device to lose the remote locking feature of the key fob. If this happens you need to bring your key fob to a technician who is skilled in chip level repairs.
Water damage
If you dropped your key fob in the pool, threw it into the wash or just left it in the rain for too long, water damage could be a real problem. Water is a good conductor and can short out circuit boards. It can also cause corrosion to the metal connections on the key fob as well as other components. A damaged circuit board could also cause the battery dump its charge.
If you have an extra key fob, try using it to lock/unlock your Peugeot 3008 to eliminate the possibility that a dead coin battery is the cause of the problem. Another issue that can prevent your key fob from working correctly is interference signals that interfere with the signal that is sent to the receiver module. These interference signals are caused by many sources that include radio transmitters within the close vicinity.
If you hear sloshing sounds coming from your Peugeot 3008 when driving this could be due to a clogged condensate evaporator drain. You can determine this by taking a look at the drain holes that are underneath your door and blowing compressed air into the drain holes. You can also use flexible wire to wiggle the drain holes and dislodge any dirt that might have built up there. The sloshing sounds can be a sign that there are air pockets in the coolant system.
A malfunctioning receiver module
The receiver module of the receiver module of a Peugeot 3008 is responsible for transmitting a remote keyless signal from the keyfob into the receiver in the car. The receiver module may be damaged, preventing the car from recognizing your key fob. Other causes of this issue are dead batteries, water damage, or interference from electronic devices that operate at the same frequency the key fob. In these instances the message "card not detected" may be displayed on the display.
There are a variety of ways to fix this problem. You can try replacing the battery or reprogramming your key fob. peugeot 307 key replacement can also start the vehicle with a spare key. If the key fob still doesn't work after following all these steps, then it may be due to a defective chip.
The best way to tell if the key fob has an issue with its chip is to remove it and clean it with paper towel and rubbing alcohol. If the chip is damaged you should purchase a new one. FB Series enclosures are designed for use with a key fob. They come with an additional coin cell battery holder that fits the most popular type of key fob batteries. The enclosures can be personalized with digital printing and CNC-machined cutouts. If your key fob was exposed to dirty or salted tap water, it is possible that the chip is infected.
Keyless entry system that isn't working properly
If you get "card not detected", this indicates that your vehicle isn't able to receive the signal from your key fob. This can be caused by many different reasons such as batteries that are weak or dead. The issue is usually resolved by pressing the start button on the key fob. In some cases however, you may need to take your key fob to an Peugeot dealership for further repairs.
The first step to fix the issue with a Peugeot 3008 key fob that doesn't open or lock the doors is to check the battery. Batteries are the most common cause of a malfunctioning fob, but there are other factors that contribute to this issue too. They include worn buttons, and water damage.
If you've recently had your Peugeot key fob exposed to clean tap water it's best to remove the battery and dry the electronic components using paper towel. You can also try isopropyl alcohol or a cleaner for this purpose. If the fob has been exposed to soapy or salty water, it's best to replace it.
If your key fob still does not work You can reset it by taking out the 12 volts battery for 15 minutes. Connect the negative cable and then the positive cable.
